CX168
8-Kanal-Leistungsendstufe für niederohmige Lasten
Features
- 100 Watt pro Kanal bei 70 Volt
- Kompakt – geringer Platzbedarf im Rack mit nur 2 HE und 35,6 cm Tiefe
- Kanalpaare für maximale Flexibilität brückbar
- Exklusive PowerLight Schaltnetzteiltechnologie sorgt für hohe Leistung bei kompakter Größe
- „Active Inrush Limiting“ (aktive Einschaltstrombegrenzung) reduziert den Einschaltstrom; keine kostspieligen Power Sequencer erforderlich
- 4 HD15 DataPort-Anschlüsse (einer pro Kanalpaar) für Steuerung und Überwachung über das Q-SYS™ Netzwerk
- Manipulationsschutz für Gain-Regler durch integrierte Sicherheitsabdeckung
- Versenkte Gain-Rastpotentiometer mit 1-dB-Schritten für schnelle und genaue Einstellungen
- Abnehmbare Euroblock-Eingänge und -Ausgänge
- DIP-Schalter für Clip-Limiter, Hochpassfilter, Bridge-Mono- und Parallelbetrieb
- Einstellbare Hochpassfilter (50 oder 75 Hz) schützen Ihre Lautsprecher und verhindern – bei minimalen Auswirkungen auf das Programmmaterial – eine Stromwandlersättigung.
- Umfangreiche Anzeigen an der Vorderseite: Signal, Clip, Protect sowie die nur bei QSC-Produkten zu findenden LEDs für Bridge-Mono- und Parallel-Input
- Umfassende Schutzschaltungen: Gleichstrom, Infraschall, thermische Überlastung und Kurzschluss
- Komplementäre bipolare High-Performance Class-AB+B-Ausgangsschaltung
- Leicht – wiegt nur 9,5 kg, was Montage und Transport erleichtert
- 3 Jahre Garantie sowie optional 3 Jahre mit erweitertem Servicevertrag
- Alle Endstufen der CX Serie erfüllen die RoHS-Richtlinie (2006) der Europäischen Union zur Beschränkung der Verwendung bestimmter gefährlicher Stoffe in Elektro- und Elektronikgeräten.
SPECIFICATIONS | CX168 | CX108V | |
STEREO MODE, All Channels Driven Continuous Average Output Power Per Channel | |||
8Ω, 0.05% THD 20 Hz–20 kHz | 90 W | - | |
4Ω, 0.1% THD 20 Hz–20 kHz | 130 W | - | |
70 V, 0.2% THD 20 Hz–20 kHz | - | - | 100 W |
Midband Ratings 8Ω, 0.1% THD 1 kHz 4Ω, 0.1% THD 1 kHz | All channels 100 W 140 W | Single channel 120 W 180 W | - - |
BRIDGE MONO MODE | |||
16Ω, 0.1% THD 20 Hz–20 kHz 8Ω, 0.1% THD 20 Hz–20 kHz 140 V, 0.2% THD 20 Hz-20 kHz | 180 W 260 W - | - - 200 W | |
Noise (20 Hz–20 kHz) | -107 dB | -100 dB | |
Input Sensitivity (for full-rated output power) | 1.35 V rms @ 8 ohms | 1.26 V rms @ 70V | |
Voltage Gain | 20× (26 dB) | 56× (35 dB) | |
Input Clipping | 6 V rms (+18 dBu) | 6 V rms (+18 dBu) | |
Output Circuitry Class | Class AB+B | Class AB+B | |
Frequency Response | 20 Hz–20 kHz, ± 0.2 dB 8 Hz–50 kHz, +0/-3 dB | 20 Hz–20 kHz, ± 0.4 dB 8 Hz–70 kHz, +0/-3 dB | |
Damping Factor | Greater than 200 (5 kHz and below) | Greater than 500 (5 kHz and below) | |
Input Impedance | 6 kΩ unbalanced, 12 kΩ balanced | 6 kΩ unbalanced, 12 kΩ balanced | |
Distortion (SMPTE-IM) | Less than 0.02% | ||
Distortion (typical) 20 Hz–20 kHz: 10 dB below rated power 1.0 kHz and below: at full rated power | Less than 0.1% THD Less than 0.03% THD | ||
Connectors | Input: 3-pin Euro-style detachable terminal blocks, (one per ch.) DataPort: HD-15 Connector, (one per channel pair: Ch 1+2, 3+4, 5+6, 7+8) Output: Two 8-pin Euro-style detachable terminal blocks | ||
Cooling | Variable speed fan, rear-to-front airflow through tunnel heat sink | ||
Controls | Front: AC switch, Ch 1, 2, 3, 4, 5, 6, 7 & 8 gain knobs Rear: DIP switches for Ch. 1–Ch. 8, clip limiter on/off, LF filter on/off, LF filter freq select 33 or 70 Hz for CX168, LF filter freq select 50 or 75 Hz for CX108V, inputs parallel or stereo; bridge mode | ||
Indicators | PWR-ON: Green LED SIGNAL-35 dB: Green LED (1 per channel) CLIP: Red LED (1 per channel) | PARALLEL INPUTS: Orange LED (1 per ch. pair) BRIDGED: Yellow LED (1 per ch. pair) | |
Amplifier Protection | Full short circuit, open circuit, thermal, ultrasonic, and RF protection; Stable into reactive or mismatched loads | ||
Load Protection | On/off muting; Individual channel DC fault blocking | ||
Dimensions (HWD) inches | 3.5 x 19 x 14 / 2RU | ||
Dimensions (HWD) mm | 89 x 483 x 356 / 2RU | ||
Weight | 21 lb (9.5 kg) net, 27 lb (12.3 kg) shipping | ||
Power Requirements | 100, 120, 230 VAC, 50–60 Hz (configured at factory) |