AcousticDesign Surface Mount

Also available in white

AcousticDesign™ surface loudspeakers offer a variety of models specifically taylored for demands of higher fidelity applications.  Designed for clarity and presense, these loudspeaker systems deliver pristine audio reproduction for installations requiring a refined audio experience.  Models ship complete with the award winning X-Mount™ system and weather input cover.

Consistent and even conical coverage is achieved through Directivity Matched Transition (DMT™), a QSC innovation which matches the directivity patterns of the woofer and the high-frequency waveguide at the crossover point. The result is a coherent transition between transducers and improved off-axis response.

AcousticDesign models with (T) suffix feature low-loss, low-saturation transformers with selectable taps, including an 8Ω bypass. To enhance weather resistance, the rotary selector is located on the back of the enclosure, protected by a weather grommet.

To further enhance performance and speed of install with optimum result, advanced voicing filter sets using QSC Intrinsic Correction™ techniques are available via Q-SYS networked audio processing or CXD amplifier platforms for a complete QSC systems solution.

Installers will appreciate the award-winning X-Mount™ system included with each full-range AcousticDesign model. This ingenious mounting solution achieves unprecedented ease-of-installation in horizontal, vertical, wall, or ceiling deployments. 

Knurled surfaces at the pivot planes ensure the load will not drift or sag over time.  Articulation marks allow pre-configuration of the X-Mount™ while on the ground with no special tools required. Once secure, the loudspeaker installs in seconds, allowing the installer to work safer, smarter, and faster with repeatable results.

Furthermore, AcousticDesign surface-mount speakers may be adapted to third-party mounting solutions or used with the following QSC ball-mount and yoke mount accessories:

                 • AD-S32T: Yoke and ball mount included
                 • AD-S52/S52T: YM-5 Yoke Mount available
                 • AD-S6T/AD-S8T/AD-S10T/AD-S12: X-Mount™
                   included, Yoke Mounts available

With rugged ABS enclosures, sealed input panel covers, and powder-coated aluminum grilles for weather resistance, the AcousticDesign surface mounted series exceed IEC60529 IP-54 ratings for dust and splash resistance.

Designed for all general audio applications, AcousticDesign surface-mount models come in a wide range of sizes, from a compact 3-inch 2-way to a dual 8-inch 2-way and even a dual 8-inch subwoofer. Several models have built-in 70/100 volt distributed line transformers.

Complimenting adjacent product families, AcousticDesign surface loudspeakers are available in QSC standard black (RAL 9011) or white (RAL 9010), and may be painted to match any decor.

SELECT A MODEL

Loudspeakers

  AD-S4T AD-S6T AD-S8T AD-S10T AD-S12
Effective frequency range1 68 - 20k Hz 60 – 20k Hz 55 – 20k Hz 50 – 19k Hz 52 – 20k Hz
Rated noise
power / voltage2		 50W / 20V (rms) 150W / 35V (rms) 200W / 40V (rms) 250W / 45V (rms) 300W / 50V (rms)
Sensitivity3 87 dB SPL 89 dB SPL 90 dB SPL 92 dB SPL 95 dB SPL
Coverage Angle
(-6 dB)		 120° conical DMT 105° conical DMT 105° conical DMT 90° conical DMT 75° conical DMT
Output4
(Peak SPL @ 1M)		 110 dB 116 dB 119 dB 122 dB 126 dB

Driver Information:

LF


HF



 		 4-inch weather resistant paper cone woofer, 1-inch / 25 mm voice-coil

0.75-inch silk dome tweeter / 0.75-inch voice coil, horn loaded		 6-inch weather resistant paper cone woofer, 1.5-inch / 38 mm voice-coil

1-inch silk dome tweeter  / 1-inch voice coil, horn loaded		 8-inch weather resistant paper cone woofer, 2-inch/ 51 mm voice-coil

1-inch exit / 1.4-inch voice-coil compression driver 		 10-inch weather resistant paper cone woofer, 2.5-inch/ 64 mm voice-coil

1-inch exit / 1.4-inch voice-coil compression driver 		 12-inch weather resistant paper cone woofer, 3-inch/ 76 mm voice-coil

1-inch exit / 1.4-inch voice-coil compression driver 
Transformer Taps 70 V: 30, 15, 7.5, 3.75 W and 8Ω bypass

100V: 30, 15, 7.5 W and 8Ω bypass		 70 V: 60, 30, 15, 7.5 W and 8Ω bypass

100V: 60, 30, 15 W and 8Ω bypass		 70 V: 100, 50, 25, 12.5 W and 8Ω bypass

100V: 100, 50, 25 W and 8Ω bypass		  N/A
Rated Impedance 8Ω
Input Connectors Euroblock connector with parallel output terminals
Enclosure Painted ABS polymer
Ingress protection IP-54
Net Weight 6.5 lb / 2.9 kg 13.6 lb / 6.2 kg 24.1 lb / 11 kg 31 lb / 15 kg 35 lb / 16 kg
  Details Details Details Details Details

1 Free-field, -10 dB from on-axis sensitivity.
2 IEC60268-1 noise signal for 2 Hrs.
3 On-Axis, free-field sensitivity, 2.83V, 1 m.
4 Calculated from rated noise voltage and sensitivity

All specifications are subject to change without notice.

Legacy Models

Model AD-S32T AD-S52T AD-S282H
Frequency Range, -10 dB 65 Hz - 20 kHz 60 Hz - 20 kHz 60 Hz - 29.5 kHz
Nominal Coverage 100° H x 100° V 90° H x 90° V 90° H x 60° V
Power Capacity1 30 W (100 hrs) 60 W (100 hrs) 450 W (8 hours)
Sensitivity2 85 dB 86 dB 93 dB
LF Driver Information 3-inch weather resistant,
polypropylene cone woofer		 5.25-inch shielded,
weather-resistant		 Dual 8-inch high power,
treated paper cone,
2-inch voice coil,
neodymium magnet
HF Driver Information 0.75-inch neodymium tweeter 1-inch neodymium tweeter 1-inch high output
compression driver
Controls / Selectors 70 V: 30, 15, 7.5, 3.8 W
100 V: 30, 15, 7.5 W
8Ω Selectable Rotary Knob		 70 V: 30, 15, 7.5 3.75 W
100 V: 30, 15, 7.5 W
8Ω Selectable
Rotary Knob		 70V 200, 100, 50, 25 W
100V 200, 100, 50 W
8Ω Selectable
Rotary Knob
Connectors Screw terminals 5-way binding
posts x 2		 Barrier strip,
(switchable: passive/active
on AD-S282H)
Dimensions (HWD) inches 26.2 x 10.2 x 11.4 11.3 x 7.0 x 8.3 -
Dimensions (HWD) mm 201 x 122 x 140 287 x 178 x 212 -
Weight 4 lb / 1.8 kg 18 lb / 8.2 kg 27.7 lb / 12.6 kg
  Details Details Details

1 Continuous IEC specified test signal, 2 hours unless otherwise stated.
2 Based on nominal impedance, measured in full space. 1 W @ 1 m.

All specifications are subject to change without notice.

Subwoofers

Model AD-S112sw
System Type 12-inch Subwoofer
Low-frequency Transducer 12-inch woofer, 2.5-inch voice coil
Frequency Response (-6 dB)1 30 Hz - 135 Hz
Filter N/A
Max Continuous Output2:
half space / full space 		 121 dB SPL / 115 dB SPL
Nominal Impedance 8Ω
Rated Noise Power 300 W (2 hours AES2 - 1984)
Sensitivity 90 dB
Transformer Type N/A
Transformer Taps N/A
Environmental Exceeds Mil Spec 810 for humidity, salt spray and dust;
IEC 60529 IP-54 splash rating
Connectors Euroblock
Dimensions (HWD) inches 23.5 x 13.9 x 12.7
Dimensions (HWD) mm 596 x 354 x 323
Weight 29 lb / 13.2 kg
  Details

1 Measured free field.
2 Pink noise within specified frequency range at 1m at rated RMS power.

All specifications are subject to change without notice.

Resources

We use cookies to understand how you use our site and to improve your experience. By continuing to use our site, you accept our use of cookies, Privacy Policy and Terms and Conditions.